Hardware Manuals


Pioneer - DDJ-1000SRT - Layout

Mixer & Effects




MIXER CONTROLS


  1. CROSSFADER. Blends audio between the channels assigned to the left and right side of the crossfader.

  2. CROSSFADER CH ASSIGN. Define if a mixer channel will be output regardless of the position of the crossfader (THRU position) or Left/Right.

  3. VOLUME. Adjust the Volume of each channel. While SHIFT is held down, the VOLUME faders will stop the deck at the previously selected Cue when these reach the minimum level (zero) and will start the deck (synced to the other deck) if those move from the zero position. (Fader Start)

  4. CUE (PFL) (per channel) Press these buttons to send each channel to the Headphones Output channel.

  5. COLOR FX PARAMETER. Adjust the parameter of the selected COLOR FX for each channel. When in middle position, the COLOR FX has no effect on the sound.

  6. LOW EQ. Adjust the Low frequencies for each mixer channel.

  7. MID EQ. Adjust the Mid frequencies for each mixer channel.

  8. HI EQ. Adjust the High frequencies for each mixer channel.

  9. TRIM. Adjust the Gain of each mixer channel.

  10. CH INPUT VUMETER. Shows each channels input (pre fader) volume.

  11. INPUT SELECTORS. Define the source of each Channel. Put the switchers to USB A or USB B position for software mixing.

  12. MASTER VOLUME. Adjust the level of the Master Output.

  13. MASTER OUTPUT VUMETER. Shows the master output volume of the unit.

  14. BOOTH MONITOR. Adjust the level of the Booth Output of the DDJ-1000SRT.

  15. MASTER CUE (PFL). Send the Master Output of the unit to the Headphones Output channel. Please note that in order to hear the Master Output on your headphones you must also turn the HEADPHONES MIXING (17) knob to the desired position.

  16. HEADPHONES VOLUME. Adjust the volume of the Headphones Channel.

  17. HEADPHONES MIXING. Adjust how the Channels and the Master Output blend at the Headphones Channel.

  18. SAMPLER VOLUME. Adjust the Master Output Volume of the VirtualDJ Sampler

  19. SAMPLER PFL. Send the sound of VirtualDJ Sampler to the Headphones Output channel.

  20. SOUND COLOR FX. Select one of the predefined Color Effects (Dub Echo, Pitch, Noise and Filter).

  21. MIC LOW EQ. Adjust the Low frequencies of MIC1 and MIC2 Inputs of the DDJ-1000SRT

  22. MIC HI EQ. Adjust the High frequencies of MIC1 and MIC2 Inputs of the DDJ-1000SRT

  23. MIC 2 VOLUME. Adjust the Volume Level of MIC2 Input of the DDJ-1000SRT

  24. MIC 1 VOLUME. Adjust the Volume Level of MIC1 Input of the DDJ-1000SRT

  25. MIC CONTROL. Turn ON and OFF the MIC1 and MIC2 Inputs of the DDJ-1000SRT or enable the auto Talk Over.

Please note that all mixer operations are hardware controlled, but their movement is visible in VirtualDJ GUI

EFFECT CONTROLS


The BEAT FX section is used to apply hardware effects to Decks, Master, Mic or Sampler.

  1. BEAT FX LCD SCREEN: Shows information about the selected effect.

  2. BEAT: Use these buttons to half/double the Beats Parameter of the selected Effect (for the Effects that are beat-aware). The beats value is displayed on the LCD screen.

  3. BEAT FX SELECT: Use this selector knob to select one of the available Beat FX. The name of the selected Effect is displayed on the LCD screen.

  4. BEAT FX ASSIGN: Use this selector knob to select to which source the effect will apply to. (Decks, Master, Mic or Sampler). The selected source will be displayed on the LCD screen.

  5. BEAT FX LEVEL: Use this knob to adjust the 1st Parameter of the selected Effect.

  6. BEAT FX ON: Use button to enable/disable the selected Beat FX. Its led will flash when enabled
Deck Controls